Tehnički kutak > Tuning skutera
Malossi - Boost bottle instalacija
Crazy Kuree:
Dobio sam bosst bottle malosijev s tim da sam dječku uštimo skuter i dao diznu svoju, u mene je minarelli znači gumena prirubnica, jel to mora na prirubnicu ili može i na karb odma do vakuma da bude (na ulazu u prirubnicu)?
Crazy Kuree:
Jel valja ova shema? https://www.pmtuning.co.uk/BOOSTBOTTLEGUIDE2.JPG i jel moram šta podešavat kao npr odaziv na gas na onom šarafiću za smjesu
Crazy Kuree:
EDIT: evo još neke informacije, održava na lamalicama pritisak (da budu skroz zatvorene kad se pusti gas) i sigurno ste primjetili da kad se vozi bez filtera da smjesu baca malo van pri puštanju gasa (kad staviš ruku blizu ulaza na karb. ruku ti malo skvasi) sa boost botleom ne pušta ni malo van smjesu (u slučaju da je filter, u njega ne pušta ni malo smjesu kad se gas pusti), "budi" mašinu s mali obrtaja, AKO SE NE INSTALIRA KAKO TREBA NE RADI , obujam boost botlla bi trebo bit kao obujam cilindra (50ccm cilndar- 50ccm boost bottle)
vasso123:
Daj jbt nemozes samo pisat iz glave,pokusaj to napisat i da te drugi skuze... :angry7:
Crazy Kuree:
--- Citat: vasso123 - 04 Rujan, 2008, 22:12:57 ---Daj jbt nemozes samo pisat iz glave,pokusaj to napisat i da te drugi skuze... :angry7:
--- Kraj citata ---
eto nadam se da sad kužiš, a treba mi netko da mi ovo prevede točno je napisano što treba uradit:
1) Remove air box from sled.
2) Remove carbs from carb adapters (carb boots)
3) Remove carb adapters from reed cage.
4) Using an "Exacto" type razor knife, cut the plug out of the snorkel tubes in the top of
the carb adapters or use a 1/4" track drill to drill three offset holes in each snorkel tube.
Some models will have a plastic reed stuffer. Continue holes through this plastic also.
5) Replace carb adapters.
6) Pull antifreeze surge bottle and hose as far forward as possible without stretching
hoses to far as to cause leaks.
7) Loosen clamps on hose coming from the bottom of the head and twist hose as close
to the cylinders as possible
8) Loop short plastic tie wraps around the rubber spigots of the carb adapters (Do not
tighten).
9) Install the SLP boost bottle into the carb adapter snorkel tubes.
10) Loop long plastic tie wrap around the boost bottle and brass fitting of the water hose
on the bottom side of the head and tighten so that the boost bottle is 1/8" from the idle
screw adjuster. NOTE: Make sure that the hose clamp on the underside of the head
is not rubbing the boost bottle.
11) Attach the Boost Bottle with plastic tie wraps to the rubber spigots securely.
12) Reinstall the carburetors and the airbox.
13) Tie wrap antifreeze surge bottle hose to the water return hose (hose coming from the
top of the head).
još nešto ler gas se poveća pa ga treba smanjit, i treba podesit odaziv na gas na onom šarafiću za smjesu ( kad najbolje prima tako ostavit), koliko sam skužio treba bit što veća rupa na šarafiću na koji se natakne crijevo
Navigacija
[0] Lista Poruka
Idi na punu verziju